|
FRONT SUSPENSION |
|
|
4930 |
Bulkheads
(l&r) (front) |
Traxxas upgrade exists |
a |
4930x |
Bulkheads, machined 6061 T-6 aluminum
(blue) (l&r) (front) (requires hinge pins) |
NEM TRM330V2 |
|
4931 |
Suspension arms
(upper/ lower) (1 each) |
UE Suspension kit |
|
4932 |
Axle carriers/
steering blocks (2) |
UE Suspension kit |
|
4933 |
Pivot balls (4)/
pivot ball cap bushings (4) |
Traxxas upgrade exists |
a |
4933x |
Pivot balls, hard anodized 7075 T-6
aluminum (4)/ pivot ball cap bushings (4) |
UE Steel pillowballs |
|
4934 |
Aluminum caps,
pivot ball (4) |
UE Suspension kit |
a |
4934x |
Aluminum caps, pivot ball (blue) (4) |
Not
Needed, same as above |
|
4917 |
Shock tower |
UE suspendion kit |
Back
to the top |
|
DRIVELINE |
|
|
4927 |
Transmission
output yokes (2)/ set screw yoke pins, 4x5x10mm (1) &
4x7.5x18.5mm (1) |
UE Chassis kit |
|
4928 |
Differential output yokes (2)/
set screw yoke pins, 4x5x10mm (2) |
UE CVD kit |
|
4949 |
Half shafts, short
(external-splined (2) & internal-splined (2))/ metal
u-joints (4) |
UE Chassis kit |
|
4951 |
Half shafts, long
(external-splined (2) & internal-splined (2))/ metal
u-joints (4) |
UE CVD kit |
a |
4950 |
Half shaft
multi-pack, short (internal-splined (6)/ external-splined
(6)) (plastic shafts only) |
Plastic |
a |
4952 |
Half shaft
multi-pack, long (internal-splined (6)/ external-splined
(6)) (plastic shafts only) |
Plastic |
|
4953 |
Stub axles (2) |
UE CVD kit |
|
4932 |
Axle carriers (2) |
Exists in suspension section |
|
4954 |
Hex wheel hubs (2)/ axle pins
(2.5x12mm) (2) |
Traxxas upgrade available |
a |
4954x |
Hex wheel
hubs, 6061 T-6 aluminum (blue) (2)/ axle pins
(2.5x10mm) (2) |
UE CVD kit |
|
4955 |
Pins, axle (2.5x12mm) (4) |
Not neede with UE CVD |
Back
to the top |
|
DIFFERENTIAL COMPONENTS |
|
2 |
4980 |
Housings, diff (ring side/
non-ring side) (1 each)/pinion collar (1) |
HCR 00322 |
2 |
4981 |
Ring gear, 37-T/ 13-T pinion/
diff carrier/ 6x10x0.5mm teflon washer (1)/ 2x8mm
countersunk machine screws (4) |
Kippster cups with modifed RRP ring gear, |
a |
4981x |
Spool (eliminates
differential-use off-road only) |
Yeah right |
2 |
4982 |
Diff gear set: 13-T output gear
shafts (2)/ 13-T spider gears (2)/ spider shaft
(1)/ 6x10x0.5mm teflon washer (1) |
Spider gears, I think these will have to
be stock, any upgrade available? |
|
1647 |
Silicone grease |
Easy to find |
Back
to the top |
|
TRANSMISSION COMPONENTS |
|
|
4989x |
Shift fork-shaft/ shift fork pads
(2)/ rubber shift shaft seal |
Not needed |
|
4990 |
Clutch bell, forward/ reverse |
Not needed |
|
4991 |
Gearbox halves (f&r)/ rubber
access plug |
Wildhobbies aluminium box halves |
|
4992 |
Drive gear, two-speed
(17/22-teeth)/ slipper shaft |
Exists in 2-speed section |
|
4993 |
Gear shaft, primary(1) |
UE transmission kit |
|
4994 |
Output shaft (1)/ output shaft
spacer (5x8x14mm) |
UE transmission kit |
|
4995 |
Primary gears: forward (28-T)/ reverse (22-T)/
steel drive pin (2x9.8mm)/ 5x10x0.5mm teflon washer (1) |
UE transmission kit |
|
4996 |
Idler gear, steel (16-tooth)/
idler gear shaft/ 3x8mm flat metal washer/ 8x12x0.5mm
teflon washer/ 3x6mm flat metal washer/ 3mm nylon locknut
3x20mm cap hex machine screw |
Not needed |
|
4997 |
Output gear assembly, forward
(26-T) |
UE transmission kit |
|
4998 |
Output gear assembly, reverse
(26-T) |
Not needed |
Back
to the top |
|
2-SPEED COMPONENTS |
|
|
4992x |
Drive gear, two-speed
(17/22-teeth)/ slipper shaft |
stock |
|
4984 |
Spur gear, 43-T (1st speed) |
stock |
|
4985 |
Spur gear assembly, 38-T (2nd
speed) |
stock |
|
4986 |
Gear hub assembly, 1st/ one-way
bearing/ snap ring |
stock |
|
4987 |
Rings, snap (14mm) (2) |
stock |
|
4889 |
Ball bearing (1)(10x19x5mm) |
See Bearing section |
|
4988 |
Drive hub assembly, clutch/
6x8.5x0.5mm teflon washer (1) |
stock |
|
4897 |
Grub screws, 4mm (6)
(threadlocked) |
common |
Back
to the top |
|
SPUR GEARS AND RELATED PARTS |
|
|
4472x |
Spur gear (72-tooth) (32-pitch) |
Get the smaller one |
a |
4470 |
Spur gear
(70-tooth) (32-pitch) |
RRP 8565 65 tooth wheel. |
|
4685 |
Friction pegs, slipper (12) |
stock |
|
4622 |
Pressure rings, slipper (notched)
(2) |
stock |
|
4625 |
Pressure plate, slipper (1) |
stock |
|
4992 |
Drive gear, two-speed
(17/22-teeth)/ slipper shaft |
Exists in 2-speed section |
|
1994 |
Slipper tension spring/ spur gear
bushing & locknut |
stock |
Back
to the top |
|
THROTTLE, BRAKE, & SHIFT
LINKAGE |
|
|
3180x |
Rod guides (2)/ nuts (2) |
Common part |
|
4182 |
Servo horn, throttle-brake/ shift
(1) |
Common part |
|
3182 |
Collars, screw (2)/ grub screws,
3mm (2) |
Common part |
|
4967 |
Brake cam (blue)/ cam lever/ 3mm
grub screw |
Exists in brake section |
|
4968 |
Wires: brake/ throttle/ shift;
servo horns: throttle/ brake & shift; ball screw and
ball cup (shift shaft) |
Should be able to make this part |
|
3184 |
Springs: throttle, brake, &
shift (3) |
Easily sourceable |
Back
to the top |
|
CHASSIS AND ATTACHMENTS |
|
|
4922 |
Chassis, 6061 T-6 aluminum
(2.5mm) (blue) |
Traxxas upgrade available |
a |
4922x |
Chassis, 7075 T-6
billet machined aluminum (4mm) (blue)/ hardware |
UE chassis kit |
|
4923 |
Chassis braces, lower (2) |
Traxxas upgrade available |
a |
4923x |
Chassis braces,
lower machined 6061 T-6 aluminum (blue) (2)/ hardware |
UE chassis kit |
|
4924 |
Box, receiver/ x-tal access
rubber plug/ adhesive foam chassis pad |
MTC 22202 |
|
4925 |
Box, battery/ adhesive foam
chassis pad |
MTC 22201c |
|
3170 |
Battery holder, 4-cell/ on-off
switch |
I'll supply this |
Back
to the top |
|
ENGINE AND SERVO MOUNTS |
|
|
4918 |
Servo mounts, steering/ shift
(f&r) |
Traxxas upgradeable |
a |
4918x |
Servo mounts,
steering/ shift (machined aluminum)(blue) (f&r)/
machine screws (8) |
UE chassis kit |
|
4919 |
Servo mounts, throttle/ brake (1) |
Traxxas upgradeable |
a |
4919x |
Servo mounts,
throttle/ brake (machined aluminum)(blue) (f&r)/
machine screws (8) |
UE chassis kit |
|
4960 |
Engine mount, aluminum (w/
screws) |
Traxxas upgradeable |
a |
4960x |
Engine mount,
machined 6061 T-6 aluminum (blue) (w/ screws) |
UE chassis kit .40FS eventually |
Back
to the top |
|
BODY & ACCESSORIES |
|
|
4911 |
Body, T-Maxx |
No body, using a roll cage |
|
4913 |
Decal sheet, T-Maxx |
No body, using a roll cage |
a |
4913x |
Decal sheet, Jaws
T-Maxx |
No body, using a roll cage |
|
2514 |
Decal sheet, racing sponsors |
No body, using a roll cage |
a |
9950 |
Official Team
Traxxas racing decal set (flag logo/ 6-color) |
No body, using a roll cage |
|
4914 |
Body mount posts, front (2)/ body
mount plate (f)/ body mount screw pins (f) (2)/ body
mount (r)/ EZ-Start receptacle retainer/ screws |
UE Suspension kit |
|
4915 |
Body washers, foam adhesive (10) |
No body, using a roll cage |
|
1834 |
Body clips (12) |
No body, using a roll cage |
|
1726 |
Antenna, tube |
Common |
|
1926 |
Antenna caps, vinyl (2)/ antenna
spool |
Common |
|
4999 |
Operating instructions, T-Maxx |
It's not a Traxxas |
Back
to the top |
|
CLUTCH &
RELATED PARTS |
|
|
4146x |
Clutch shoes/ spring (for higher
stall) |
MIP clutch |
|
3281 |
Cone, split beveled |
stock |
|
4142 |
Flywheel |
RRP 8550 vented fly wheel |
|
4144 |
Clutch adapter nut and shaft |
UE clutch nut and
shaft |
|
1633 |
E-clips/ C-rings |
Any hardware store should have these |
a |
4118 |
Clutch bell,
steel replacement (18-tooth)/ 5x8x0.5mm fiber washer (2)/
5mm E-clip (requires #4609 - ball bearings, 5x10x4mm (2)) |
Bigger needed |
|
4120 |
Clutch bell, steel replacement
(20-tooth)/ 5x8x0.5mm fiber washer (2)/ 5mm E-clip
(requires #4611-ball bearings, 5x11x4mm (2)) |
Bigger needed |
a |
4122 |
Clutch bell,
steel replacement (22-tooth)/ 5x8x0.5mm fiber washer (2)/
5mm E-clip (requires #4611-ball bearings, 5x11x4mm (2)) |
any upgrade available??
stock, not sure with a .40FS engine on a SM chassis |
a |
4609 |
Ball bearings,
5x10x4mm (2) |
See Bearing section |
a |
4611 |
Ball bearings,
5x11x4mm (2) |
See Bearing section |
Back
to the top |
|
SHOCKS |
|
|
ULTRA
SHOCKS |
|
|
3762x |
Ultra shocks (black) (xx-long) (2) |
Stock |
|
2362 |
Shock rebuild kit (for 2 shocks) |
Stock |
|
1765 |
Rubber diaphragms (4) |
Stock |
|
2656 |
Shock shafts, hard chrome (xx-long) (2) |
Stock |
|
3768 |
Spring retainers, upper & lower (2)/
piston head set (2-hole (2)/ 3-hole (2)) |
Stock |
|
3769 |
Spring pre-load spacers: 1mm (4)/ 2mm (2)/
4mm (2)/ 8mm (2) |
Stock |
|
3642 |
Attachment screws (3x12 shoulder screws)
(6) |
Stock |
a |
2667 |
Shock caps, aluminum (2) |
Stock |
|
4957 |
Springs,(for ultra shocks only) red (2.5
rate) (f/r) (2) |
Stock |
|
1666 |
Silicone damper oil |
50wt |
|
OPTIONAL PRO-LEVEL ALUMINUM |
|
a |
2662 |
Big-bore shocks (xx-long)
(hard-anodized & teflon-coated T-6 alum) w/o springs
(2) |
Not needed |
a |
4962 |
Big-bore shocks (xx-long)
(hard-anodized & teflon-coated T-6 alum) w/ red
springs (8 pack) |
Progressive suspension EDC-2
Trinity Black Monster
Springs |
a |
2362 |
Shock rebuild kit (for 2 shocks) |
Not needed |
a |
1765 |
Rubber diaphragms (4) |
Not needed |
a |
2656 |
Shock shafts, hard chrome
(xx-long) (2) |
Not needed |
a |
2668 |
Spring retainers, upper &
lower (2)/ spring pre-load spacers: 1mm (4)/ 1.5mm (2)/
2mm (2)/ 4mm (2)/ 8mm (2) |
Not needed |
a |
2669 |
Piston head set (2-hole (2)/
3-hole (2)) / shock mounting bushings & washers (2) |
Not needed |
a |
2666 |
Big bore shock cylinder (xx-long)
(1) |
Not needed |
a |
2667 |
Shock caps, Big-bore (2) |
Not needed |
a |
4649r |
Springs, red (2.75") (2.5
rate) (2) |
Not needed |
a |
1666 |
Silicone shock oil |
50wt |
Back to the top |
|
LINKAGE |
|
|
4939 |
Suspension screw pin set |
Upgrade
available |
a |
4939x |
Suspension pin set, stainless
steel (w/ E-clips) |
Upgrade available |
a |
4939r |
Suspension pin set, titanium (w/
E-clips) |
UE Suspension kit |
|
3642 |
Attachment screws, shock (3x12mm shoulder
screws) (6) |
Exists in shock section |
|
2338 |
Turnbuckles, 96mm (front tie rods) (2) |
Upgrade
available |
a |
2338x |
Turnbuckles, titanium 94mm (front
tie rods) (2)/ billet aluminum wrench |
UE Suspension kit |
|
2339 |
Turnbuckles, 105mm (rear toe control
links) (2) |
Upgrade
available |
a |
2339x |
Turnbuckles, titanium 105mm (rear
toe control links) (2)/ billet aluminum wrench |
UE Suspension kit |
|
2742 |
Rod ends (long) (6)/ hollow ball
connectors (6) |
UE Suspension kit |
|
1942 |
Rod ends (16 long & 4 short)/ hollow
ball connectors (18)/ ball screws (2) |
UE Suspension kit |
|
3744 |
Servo saver |
Exists in steering section |
Back to the top |
|
FUEL &
RELATED ITEMS |
|
a |
5010x |
Top Fuel, 10% Nitro (quart) |
I'll get my own |
a |
5020 |
Top Fuel, 20% Nitro (quart) |
I'll get my own |
a |
5060 |
Top Fuel, 10% Nitro (gallon) |
I'll get my own |
a |
5070 |
Top Fuel, 20% Nitro (gallon) |
I'll get my own |
a |
5050 |
Car cleaner, Nitro Wash (quart) |
Degreaser |
a |
5001 |
Bottle, Fuel filler (500cc) |
I'll get my own |
a |
3230 |
Glowplug, standard (long-hot) |
I'll get my own |
a |
3231 |
Glowplug, heavy-duty
(long-medium) |
I'll get my own |
Back to the top |